17 Best 10 24 Threads in 2020

 

Steel Thread Cutting Screw Zinc Plated 82 Degree Flat Undercut Head Phillips Drive Type 23 10-24 Thread Size 38 Length Pack of 100 #ad

Steel Thread Cutting Screw, Zinc Plated, 82 Degree Flat Undercut Head, Phillips Drive, Type 23, #10-24 Thread Size, 3/8″ Length (Pack of 100)

Steel Thread Cutting Screw, Zinc Plated, 82 Degree Flat Undercut Head, Phillips Drive, Type 23, #10-24 Thread Size, 3/8″ Length (Pack of 100) #ad - Zinc plating resists corrosion and has a reflective appearance. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Thread cutting screw with type 23 point style has fine threads that taper down to a blunt point with a large cutting surface suitable for soft metal, provides excellent chip clearance, and requires minimal rotating force to install. Steel is often used in applications where strength is the primary consideration.

 

Steel Self-Drilling Screw Zinc Plated Finish Wafer Head Star Drive 3 Drill Point 10-24 Thread Size 1-12 Length Pack of 50 #ad

Steel Self-Drilling Screw, Zinc Plated Finish, Wafer Head, Star Drive, #3 Drill Point, #10-24 Thread Size, 1-1/2″ Length (Pack of 50)

Steel Self-Drilling Screw, Zinc Plated Finish, Wafer Head, Star Drive, #3 Drill Point, #10-24 Thread Size, 1-1/2″ Length (Pack of 50) #ad - Zinc plating resists corrosion and has a reflective appearance. Steel is often used in applications where strength is the primary consideration. Wafer head has a flat top, a 70-degree cone-shaped bearing surface, and a small slope between the top and the bearing surface. Star drive has a six-pointed indentation that provides a large contact area for the driver, resisting slippage better than a phillips or slotted drive.

 

Morris Products 18420 Bolt-On Bridle Ring 10-24 Thread Size 1 Diameter Size Pack of 50 #ad

Morris Products 18420 Bolt-On Bridle Ring, 10-24 Thread Size, 1″ Diameter Size (Pack of 50)

Morris Products 18420 Bolt-On Bridle Ring, 10-24 Thread Size, 1″ Diameter Size (Pack of 50) #ad - Supports communications cable & other low voltage uses. Zinc plated steel. Bridle rings, bolt-on, commonly used with beam clamps supports communications cable & other low voltage uses. Commonly used with beam clamps. Culus listed.

 

Steel Machine Screw Zinc Plated Finish Pan Head Phillips Drive 1-14 Length 10-24 Threads Pack of 100 #ad

Steel Machine Screw, Zinc Plated Finish, Pan Head, Phillips Drive, 1-1/4″ Length, #10-24 Threads (Pack of 100)

Steel Machine Screw, Zinc Plated Finish, Pan Head, Phillips Drive, 1-1/4″ Length, #10-24 Threads (Pack of 100) #ad - Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Zinc plating resists corrosion resistance and has a reflective appearance. Pan head has a flat top and short vertical sides with a rounded top edge. Steel is often used in applications where strength is the primary consideration.

 

Small Parts FSC1058CBSS Round Square-Neck Carriage Bolt 18-8 Stainless Steel Hex 10-24 Thread Size 58 Long Pack of 50 #ad

Small Parts FSC1058CBSS Round Square-Neck Carriage Bolt, 18-8 Stainless Steel, Hex, 10″-24″ Thread Size, 5/8″ Long (Pack of 50)

Small Parts FSC1058CBSS Round Square-Neck Carriage Bolt, 18-8 Stainless Steel, Hex, 10″-24″ Thread Size, 5/8″ Long (Pack of 50) #ad - Material 18-8 stainless steel. Round square-neck carriage bolt, 18-8 stainless steel, hex, 10″-24″ thread size, 5/8″ long (pack of 50). Length 5/8 inch. Thread size #10-24.

 

ASME B1863 Plain Brass Machine Screw Hex Nut 10-24 Thread Size 18 Width Across Flats 38 Thick Pack of 100 #ad

ASME B18.6.3 Plain Brass Machine Screw Hex Nut, #10-24 Thread Size, 1/8″ Width Across Flats, 3/8″ Thick (Pack of 100)

ASME B18.6.3 Plain Brass Machine Screw Hex Nut, #10-24 Thread Size, 1/8″ Width Across Flats, 3/8″ Thick (Pack of 100) #ad - Hex nuts are appropriate for use in low-strength assemblies. Ensure a lasting hold for any project. Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads. Drive system is a hexagon-shaped head. Brass is suitable where corrosion resistance is a primary consideration.

 

Nylon 66 Thumb Screw Plain Finish White Knurled Head Slotted Drive Flat Point Meets ASTM D4066ASTM D6779 18 Length Fully Threaded 10-24 Threads Pack of 100 #ad

Nylon 6/6 Thumb Screw, Plain Finish, White, Knurled Head, Slotted Drive, Flat Point, Meets ASTM D4066/ASTM D6779, 1/8″ Length, Fully Threaded, #10-24 Threads (Pack of 100)

Nylon 6/6 Thumb Screw, Plain Finish, White, Knurled Head, Slotted Drive, Flat Point, Meets ASTM D4066/ASTM D6779, 1/8″ Length, Fully Threaded, #10-24 Threads (Pack of 100) #ad - Thumb screws allow for simple “by-hand” installation. Knurled head provides extra grip for manual tightening. Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations. Driven by a flat-bladed driver. Coarse threads are better for brittle materials, and will assemble and disassemble more quickly than fine threads.

 

Small Parts FSC102CBZ Round Zinc Plated Square-Neck Carriage Bolt Steel Hex 10-24 Thread Size 2 Long Pack of 100 #ad

Small Parts FSC102CBZ Round Zinc Plated Square-Neck Carriage Bolt, Steel, Hex, 10″-24″ Thread Size, 2″ Long (Pack of 100)

Small Parts FSC102CBZ Round Zinc Plated Square-Neck Carriage Bolt, Steel, Hex, 10″-24″ Thread Size, 2″ Long (Pack of 100) #ad - Round zinc plated square-neck carriage bolt, steel, hex, low-strength, 10″-24″ thread size, 2″ long (pack of 100). Thread size #10-24. Material steel. Length 2 inch.

 

Steel Pan Head Machine Screw Black Zinc Plated Meets ASME B1863 T25 Star Drive 10-24 Thread Size 34 Length Fully Threaded Imported Pack of 50 #ad

Steel Pan Head Machine Screw, Black Zinc Plated, Meets ASME B18.6.3, T25 Star Drive, #10-24 Thread Size, 3/4″ Length, Fully Threaded, Imported (Pack of 50)

Steel Pan Head Machine Screw, Black Zinc Plated, Meets ASME B18.6.3, T25 Star Drive, #10-24 Thread Size, 3/4″ Length, Fully Threaded, Imported (Pack of 50) #ad - Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Zinc plating resists corrosion and has a reflective appearance. Steel is often used in applications where strength is the primary consideration. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Thread cutting screw with type 23 point style has fine threads that taper down to a blunt point with a large cutting surface suitable for soft metal, provides excellent chip clearance, and requires minimal rotating force to install.

 

Steel Tapped-Hole U-Style Clip-On Nut Plain Finish 10-24 Thread Size For 0025-0125 Material Thickness 0468 Edge Distance Pack of 25 #ad

Steel Tapped-Hole U-Style Clip-On Nut, Plain Finish, #10-24 Thread Size, For 0.025″-0.125″ Material Thickness, 0.468″ Edge Distance (Pack of 25)

Steel Tapped-Hole U-Style Clip-On Nut, Plain Finish, #10-24 Thread Size, For 0.025″-0.125″ Material Thickness, 0.468″ Edge Distance (Pack of 25) #ad - Hole is tapped, or fully threaded, for screws that need to extend beyond the bottom of the nut. Plain surface has no. Steel is often used in applications where strength is the primary consideration. Clip is u-shaped for a secure hold on both sides of the panel when screwing down. Designed to clip onto panels for quick alignment and fasten with a machine screw for a secure hold.

 

Steel Truss Head Machine Screw Black Oxide Finish Meets ASME B1863 2 Phillips Drive 10-24 Thread Size 34 Length Fully Threaded Imported Pack of 100 #ad

Steel Truss Head Machine Screw, Black Oxide Finish, Meets ASME B18.6.3, #2 Phillips Drive, #10-24 Thread Size, 3/4″ Length, Fully Threaded, Imported (Pack of 100)

Steel Truss Head Machine Screw, Black Oxide Finish, Meets ASME B18.6.3, #2 Phillips Drive, #10-24 Thread Size, 3/4″ Length, Fully Threaded, Imported (Pack of 100) #ad - They are available with a variety of head shapes, which determine how the screw interacts with the mating surface, and drive styles, which determine the type of driver required to install and remove the screw. Machine screws are threaded fasteners that are typically used with nuts or drilled and tapped (threaded) holes.

 

18-8 Stainless Steel Thread Rolling Screw for Metal Passivated Finish Pan Head Star Drive 10-24 Thread Size 34 Length Pack of 25 #ad

18-8 Stainless Steel Thread Rolling Screw for Metal, Passivated Finish, Pan Head, Star Drive, #10-24 Thread Size, 3/4″ Length (Pack of 25)

18-8 Stainless Steel Thread Rolling Screw for Metal, Passivated Finish, Pan Head, Star Drive, #10-24 Thread Size, 3/4″ Length (Pack of 25) #ad - Passivated finish enhances the natural corrosion resistance of stainless steel. Pan head has a flat top and short vertical sides with a rounded top edge. Thread rolling screw recommended for use in metal. 18-8 stainless steel provides good corrosion resistance and strength. Star drive has a six-pointed indentation that provides a large contact area for the driver, resisting slippage better than a phillips or slotted drive.

 

410 Stainless Steel Self-Drilling Screw Plain Finish Wafer Head Phillips Drive 3 Drill Point 10-24 Thread Size 1-12 Length Pack of 25 #ad

410 Stainless Steel Self-Drilling Screw, Plain Finish, Wafer Head, Phillips Drive, #3 Drill Point, #10-24 Thread Size, 1-1/2″ Length (Pack of 25)

410 Stainless Steel Self-Drilling Screw, Plain Finish, Wafer Head, Phillips Drive, #3 Drill Point, #10-24 Thread Size, 1-1/2″ Length (Pack of 25) #ad - Wafer head has a flat top, a 70-degree cone-shaped bearing surface, and a small slope between the top and the bearing surface. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. 410 stainless steel has high strength and hardness ratings and resists corrosion in mild environments. Plain surface has no finish or coating.

 

Stainless Steel Machine Screw Plain Finish Pan Head Phillips Drive 2-12 Length 10-24 Threads Pack of 100 #ad

Stainless Steel Machine Screw, Plain Finish, Pan Head, Phillips Drive, 2-1/2″ Length, #10-24 Threads (Pack of 100)

Stainless Steel Machine Screw, Plain Finish, Pan Head, Phillips Drive, 2-1/2″ Length, #10-24 Threads (Pack of 100) #ad - Plain surface has no finish or coating. Stainless steel provides corrosion resistance. Pan head has a flat top and short vertical sides with a rounded top edge. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening.

 

Stainless Steel Machine Screw Plain Finish Fillister Head Slotted Drive Meets ASME B1863 58 Length Fully Threaded 10-24 Threads Pack of 100 #ad

Stainless Steel Machine Screw, Plain Finish, Fillister Head, Slotted Drive, Meets ASME B18.6.3, 5/8″ Length, Fully Threaded, #10-24 Threads (Pack of 100)

Stainless Steel Machine Screw, Plain Finish, Fillister Head, Slotted Drive, Meets ASME B18.6.3, 5/8″ Length, Fully Threaded, #10-24 Threads (Pack of 100) #ad - Meets asme b1863 specifications. Plain surface has no finish or coating. Stainless steel provides corrosion resistance. Fillister head has a slightly rounded top and tall cylindrical sides, enabling a deep drive slot for high driving force. Slotted drive has a linear slot for use with a flat-blade driver.

 

Small Parts FSC10HNSZ Low-Strength Steel Hex Nut Zinc Plated 10-24 Thread Size Pack of 100 #ad

Small Parts FSC10HNSZ Low-Strength Steel Hex Nut, Zinc Plated, 10″-24″ Thread Size (Pack of 100)

Small Parts FSC10HNSZ Low-Strength Steel Hex Nut, Zinc Plated, 10″-24″ Thread Size (Pack of 100) #ad - Fastcom supply specializes in various fasteners that span across electronic, transportation, construction, commercial and military industries.

 

Union Butterfield 1587UNC High-Speed Steel Spiral Flute Tap High-Helix Uncoated Bright Finish Round Shank with Square End Bottoming Chamfer 10-24 Thread Size #ad

Union Butterfield 1587(UNC) High-Speed Steel Spiral Flute Tap, High-Helix, Uncoated (Bright) Finish, Round Shank with Square End, Bottoming Chamfer, 10-24 Thread Size

Union Butterfield 1587(UNC) High-Speed Steel Spiral Flute Tap, High-Helix, Uncoated (Bright) Finish, Round Shank with Square End, Bottoming Chamfer, 10-24 Thread Size #ad - Higher helix angle improves chip removal. Spiral flutes for creating threads in blind holes. Available in unc (unified coarse) or unf (unified fine) right-hand thread options for different applications. Spiral flute tap design pulls chips back from the tip of the tool and out of the hole to prevent clogging. Round shank with square end helps to minimize rotation in the tool holder.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.