21 Coolest Texas Pneumatic Tools

 

Texas Pneumatic Tools Inc 8 Diameter Venturi Air Mover wSteel Horn TX-8AM

Texas Pneumatic Tools, Inc. 8″ Diameter Venturi Air Mover w/Steel Horn TX-8AM

Texas Pneumatic Tools, Inc. 8″ Diameter Venturi Air Mover w/Steel Horn TX-8AM - Moves 5,435 cfm of air when run at 100 psi and requires 178 scfm from the compressor. No moving parts/minimal maintenance. Can operate on compressed air or steam. Can be used as a blower or exhauster for ventilating hazardous areas or for cooling. Made in usa.

 

Texas Pneumatic Tools Inc 12 X 6 Air Hose Whip Assy w 34 37 oz Lubricator Chicago Coupling 12 Male NPT Swivel TX-8HW12

Texas Pneumatic Tools, Inc. 1/2″ X 6′ Air Hose Whip Assy. w/ 3/4″, 3.7 oz. Lubricator, Chicago Coupling & 1/2″ Male NPT Swivel TX-8HW1/2

Texas Pneumatic Tools, Inc. 1/2″ X 6′ Air Hose Whip Assy. w/ 3/4″, 3.7 oz. Lubricator, Chicago Coupling & 1/2″ Male NPT Swivel TX-8HW1/2 - Use a hose whip with lubricator for safety and to save money, eliminate repairs and costly downtime. Equipped with 1/2″ male npt swivel on tool end. Made in usa. 3/4″, 37 oz in line lubricator will flow up to 70 cfm at 90 psi. Crowfoot/chicago fitting on compressor end.

 

Texas Pneumatic Tools Inc 10 Diameter Venturi Air Mover wSteel Horn TX10AM

Texas Pneumatic Tools, Inc. 10″ Diameter Venturi Air Mover w/Steel Horn TX10AM

Texas Pneumatic Tools, Inc. 10″ Diameter Venturi Air Mover w/Steel Horn TX10AM - Moves 8,220 cfm of air when run at 100 psi and requires 380 scfm from the compressor. Made in usa. No moving parts/minimal maintenance. Can operate on compressed air or steam. Can be used as a blower or exhauster for ventilating hazardous areas or for cooling.

 

Texas Pneumatic Tools Inc 34 X 6 Air Hose Whip Assembly w 34 11 oz Lubricator Chicago Coupling 34 Male NPT End TX-12HW

Texas Pneumatic Tools, Inc. 3/4″ X 6′ Air Hose Whip Assembly w/ 3/4″, 11 oz. Lubricator, Chicago Coupling & 3/4″ Male NPT End TX-12HW

Texas Pneumatic Tools, Inc. 3/4″ X 6′ Air Hose Whip Assembly w/ 3/4″, 11 oz. Lubricator, Chicago Coupling & 3/4″ Male NPT End TX-12HW - Made in usa. Crowfoot/chicago fitting on compressor end. 3/4″, 11oz in line lubricator will flow up to 70 cfm at 90 psi. Equipped with 3/4″ male npt fitting on tool end. Use a hose whip with lubricator for safety and to save money, eliminate repairs and costly downtime.

 

Texas Pneumatic Tools Inc 34 X 6 Air Hose Whip Assembly w 1 16 oz Lubricator Chicago Coupling on Each End TX-15HW

Texas Pneumatic Tools, Inc. 3/4″ X 6′ Air Hose Whip Assembly w/ 1″, 16 oz. Lubricator & Chicago Coupling on Each End TX-15HW

Texas Pneumatic Tools, Inc. 3/4″ X 6′ Air Hose Whip Assembly w/ 1″, 16 oz. Lubricator & Chicago Coupling on Each End TX-15HW - 1″, 16oz in line lubricator will flow up to 150 cfm at 90 psi. Use a hose whip with lubricator for safety and to save money, eliminate repairs and costly downtime. Made in usa. Equipped with crowfoot/chicago coupling tool end. Crowfoot/chicago fitting on compressor end.

 

Texas Pneumatic Tools Inc 12 X 6 Air Hose Whip Assembly w 34 11 oz Lubricator Chicago Coupling on Each End TX-10HW

Texas Pneumatic Tools, Inc. 1/2″ X 6′ Air Hose Whip Assembly w/ 3/4″, 11 oz. Lubricator & Chicago Coupling on Each End TX-10HW

Texas Pneumatic Tools, Inc. 1/2″ X 6′ Air Hose Whip Assembly w/ 3/4″, 11 oz. Lubricator & Chicago Coupling on Each End TX-10HW - Use a hose whip with lubricator for safety and to save money, eliminate repairs and costly downtime. 3/4″, 11oz in line lubricator will flow up to 70 cfm at 90 psi. Equipped with crowfoot/chicago coupling tool end. Crowfoot/chicago fitting on compressor end. Made in usa.

 

Texas Pneumatic Tools Inc 60 Lb JackhammerPaving Breaker w 1-18 Chuck TX60PB-1125

Texas Pneumatic Tools, Inc. 60 Lb. Jackhammer/Paving Breaker w/ 1-1/8″ Chuck TX60PB-1.125

Texas Pneumatic Tools, Inc. 60 Lb. Jackhammer/Paving Breaker w/ 1-1/8″ Chuck TX60PB-1.125 - Made in usa. 1,400 blows per minute. Requires 1-1/8″ x 6″ shank chisels. We recommend the texas pneumatic tx15hw hose whip assembly for use with this tool for the correct fittings and appropriately sized in line lubricator. 67 pound net weight, 25625″ overall length, requires 59 cfm of air at 90 psi.

 

Texas Pneumatic Tools Inc 3 Diameter Short Horn Venturi Air Mover wSteel Horn TX-3AMS

Texas Pneumatic Tools, Inc. 3″ Diameter Short Horn Venturi Air Mover w/Steel Horn TX-3AMS

Texas Pneumatic Tools, Inc. 3″ Diameter Short Horn Venturi Air Mover w/Steel Horn TX-3AMS - Can be used as a blower or exhauster for ventilating hazardous areas or for cooling. No moving parts/minimal maintenance. Made in usa. Moves 1,205 cfm of air when run at 100 psi and requires 51 scfm from the compressor. Can operate on compressed air or steam.

 

Texas Pneumatic Tools Inc 12 X 6 Air Hose Whip Assembly w 34 11 oz Lubricator Chicago Coupling 12 Male NPT End TX-11HW

Texas Pneumatic Tools, Inc. 1/2″ X 6′ Air Hose Whip Assembly w/ 3/4″, 11 oz. Lubricator, Chicago Coupling & 1/2″ Male NPT End TX-11HW

Texas Pneumatic Tools, Inc. 1/2″ X 6′ Air Hose Whip Assembly w/ 3/4″, 11 oz. Lubricator, Chicago Coupling & 1/2″ Male NPT End TX-11HW - Equipped with 1/2″ male npt fitting on tool end. Crowfoot/chicago fitting on compressor end. 3/4″, 11oz in line lubricator will flow up to 70 cfm at 90 psi. Use a hose whip with lubricator for safety and to save money, eliminate repairs and costly downtime. Made in usa.

 

Texas Pneumatic Tools Inc 3 Stroke 4 Bolt Chipping Hammer w Quick Change Retainer for Round Shank Chisels TXCH3-4B

Texas Pneumatic Tools, Inc. 3″ Stroke, 4 Bolt Chipping Hammer w/ Quick Change Retainer for Round Shank Chisels TXCH3-4B

Texas Pneumatic Tools, Inc. 3″ Stroke, 4 Bolt Chipping Hammer w/ Quick Change Retainer for Round Shank Chisels TXCH3-4B - 1,650 blows per minute, 3″ stroke, 1-1/8″ bore. Quick change retainer for round shank chisels. Supplied with 6′ hose whip, in line lubricator, chicago coupling, one flat chisel and one moil point chisel. 33-35 cfm of air consumed at 90 psi. Made in usa.

 

Texas Pneumatic Tools Inc 60 Lb JackhammerPaving Breaker w 1-14 Chuck TX60PB-125

Texas Pneumatic Tools, Inc. 60 Lb. Jackhammer/Paving Breaker w/ 1-1/4″ Chuck TX60PB-1.25

Texas Pneumatic Tools, Inc. 60 Lb. Jackhammer/Paving Breaker w/ 1-1/4″ Chuck TX60PB-1.25 - 67 pound net weight, 25625″ overall length, requires 59 cfm of air at 90 psi. Requires 1-1/4″ x 6″ shank chisels. 1,400 blows per minute. Made in usa. We recommend the texas pneumatic tx15hw hose whip assembly for use with this tool for the correct fittings and appropriately sized in line lubricator.

 

Texas Pneumatic Tools Inc Pneumatic Chisel Scaler w Lever Throttle TX1BLTCS

Texas Pneumatic Tools, Inc. Pneumatic Chisel Scaler w/ Lever Throttle TX1BLTCS

Texas Pneumatic Tools, Inc. Pneumatic Chisel Scaler w/ Lever Throttle TX1BLTCS - 1″ bore, 1-1/8″ stroke, 4,600 blows per minute, requires 12 cfm @ 90 psi. Can be converted to a needle scaler (required parts sold separately). Proven throughout industrial job ites as well as in the construction and marine repair industries. Made in usa. Excellent for removing paint, rust and dirt on metals or chipping stone, concrete & brick.

 

Texas Pneumatic Tools Inc 11 Stroke Rivet Buster for 866 Jumbo Chisels TX133-11RB

Texas Pneumatic Tools, Inc. 11″ Stroke Rivet Buster for .866″ Jumbo Chisels TX133-11RB

Texas Pneumatic Tools, Inc. 11″ Stroke Rivet Buster for .866″ Jumbo Chisels TX133-11RB - In addition, the tool is shipped with a tx133kit repair kit that includes the components to replace the common wear parts in the chuck twice. The all steel throttle valve is precisely machined to a clearance measured in tenths of thousands of an inch. Every tool is supplied with a 6′ hose whip w/swivel and strain relief, in line filter/oiler, chicago/crowfoot air coupling, flat chisel and moil point chisel so the tool is ready to work as shipped right out of the box. This tool represents one of the best values on the market. Texas pneumatic rivet busters are made entirely in the usa.

 

Texas Pneumatic Tools Inc 30 Lb JackhammerPaving Breaker w 78 Chuck TX30PB-875

Texas Pneumatic Tools, Inc. 30 Lb. Jackhammer/Paving Breaker w/ 7/8″ Chuck TX30PB-.875

Texas Pneumatic Tools, Inc. 30 Lb. Jackhammer/Paving Breaker w/ 7/8″ Chuck TX30PB-.875 - We recommend the texas pneumatic tx9hw hose whip assembly for use with this tool for the correct fittings and appropriately sized in line lubricator. 1,550 blows per minute. Requires 7/8″ x 3-1/4″ shank chisels. Made in usa. 34 pound net weight, 22-1/2″ overall length, requires 49 cfm of air at 90 psi.

 

Texas Pneumatic Tools Inc 6 Diameter Venturi Air Mover wSteel Horn TX-6AM

Texas Pneumatic Tools, Inc. 6″ Diameter Venturi Air Mover w/Steel Horn TX-6AM

Texas Pneumatic Tools, Inc. 6″ Diameter Venturi Air Mover w/Steel Horn TX-6AM - No moving parts/minimal maintenance. Can be used as a blower or exhauster for ventilating hazardous areas or for cooling. Can operate on compressed air or steam. Made in usa. Moves 3,698 cfm of air when run at 100 psi and requires 101 scfm from the compressor.

 

Texas Pneumatic Tools Inc 34 X 6 Air Hose Whip Assembly w 1 16 oz Lubricator Chicago Coupling 34 Male NPT End TX-16HW

Texas Pneumatic Tools, Inc. 3/4″ X 6′ Air Hose Whip Assembly w/ 1″, 16 oz. Lubricator, Chicago Coupling & 3/4″ Male NPT End TX-16HW

Texas Pneumatic Tools, Inc. 3/4″ X 6′ Air Hose Whip Assembly w/ 1″, 16 oz. Lubricator, Chicago Coupling & 3/4″ Male NPT End TX-16HW - 1″, 16oz in line lubricator will flow up to 150 cfm at 90 psi. Use a hose whip with lubricator for safety and to save money, eliminate repairs and costly downtime. Crowfoot/chicago fitting on compressor end. Equipped with 3/4″ male npt fitting on tool end. Made in usa.

 

Texas Pneumatic Tools Inc 3 Stroke 4 Bolt Chipping Hammer w Quick Change Retainer for Hex Shank Chisels TXCH3-4B-H

Texas Pneumatic Tools, Inc. 3″ Stroke, 4 Bolt Chipping Hammer w/ Quick Change Retainer for Hex Shank Chisels TXCH3-4B-H

Texas Pneumatic Tools, Inc. 3″ Stroke, 4 Bolt Chipping Hammer w/ Quick Change Retainer for Hex Shank Chisels TXCH3-4B-H - Made in usa. 1,650 blows per minute, 3″ stroke, 1-1/8″ bore. Supplied with 6′ hose whip, in line lubricator, chicago coupling, one flat chisel and one moil point chisel. 33-35 cfm of air consumed at 90 psi. Quick change retainer for hex shank chisels.

 

Texas Pneumatic Tools Inc 2 Stroke 4 Bolt Chipping Hammer w Oval Collar Retainer for Round Shank Chisels TXCH2-4B-RS

Texas Pneumatic Tools, Inc. 2″ Stroke, 4 Bolt Chipping Hammer w/ Oval Collar Retainer for Round Shank Chisels TXCH2-4B-RS

Texas Pneumatic Tools, Inc. 2″ Stroke, 4 Bolt Chipping Hammer w/ Oval Collar Retainer for Round Shank Chisels TXCH2-4B-RS - Oval collar retainer for round shank chisels. Made in usa. 32-34 cfm of air consumed at 90 psi. 2,100 blows per minute, 2″ stroke, 1-1/8″ bore. Supplied with 6′ hose whip, in line lubricator, chicago coupling, one flat chisel and one moil point chisel.

 

Texas Pneumatic Tools Inc 6 Diameter Venturi Air Mover wPolymer Horn TX-6AM-P

Texas Pneumatic Tools, Inc. 6″ Diameter Venturi Air Mover w/Polymer Horn TX-6AM-P

Texas Pneumatic Tools, Inc. 6″ Diameter Venturi Air Mover w/Polymer Horn TX-6AM-P - Moves 3,698 cfm of air when run at 100 psi and requires 101 scfm from the compressor. No moving parts/minimal maintenance. Can operate on compressed air or steam. Made in usa. Can be used as a blower or exhauster for ventilating hazardous areas or for cooling.

 

Texas Pneumatic Tools Inc 6 Stroke Rivet Buster for 866 Jumbo Chisels TX133-6RB

Texas Pneumatic Tools, Inc. 6″ Stroke Rivet Buster for .866″ Jumbo Chisels TX133-6RB

Texas Pneumatic Tools, Inc. 6″ Stroke Rivet Buster for .866″ Jumbo Chisels TX133-6RB - This tool represents one of the best values on the market. Texas pneumatic rivet busters are made entirely in the usa. . The all steel throttle valve is precisely machined to a clearance measured in tenths of thousands of an inch. In addition, the tool is shipped with a tx133kit repair kit that includes the components to replace the common wear parts in the chuck twice. Every tool is supplied with a 6′ hose whip w/swivel and strain relief, in line filter/oiler, chicago/crowfoot air coupling, flat chisel and moil point chisel so the tool is ready to work as shipped right out of the box.

 

Texas Pneumatic Tools Inc 30 Lb JackhammerPaving Breaker w 1 Chuck TX30PB-1

Texas Pneumatic Tools, Inc. 30 Lb. Jackhammer/Paving Breaker w/ 1″ Chuck TX30PB-1

Texas Pneumatic Tools, Inc. 30 Lb. Jackhammer/Paving Breaker w/ 1″ Chuck TX30PB-1 - Made in usa. 1,550 blows per minute. Requires 1″ x 4-1/4″ shank chisels. We recommend the texas pneumatic tx9hw hose whip assembly for use with this tool for the correct fittings and appropriately sized in line lubricator. 34 pound net weight, 22-1/2″ overall length, requires 49 cfm of air at 90 psi.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.